In my previous post, I had discussed about different parts of a robot viz. Locomotion System, Power Supply System, Actuator System, Control System, Signal Processing System and Sensor System. In this post, we will see the Locomotion System in detail.
We all know the relation between power, torque and angular velocity (shown below). Since torque (tau) is inversely proportional to angular velocity (omega), lower angular velocity will result in higher torque. Hence, Lower speed –> Greater torque
All that matters is the torque. Greater the torque, greater the pulling capacity and durability.
Traditional motors available in the market have very high angular velocity, undesirable for robotic usage (since torque is very low). Hence, we need to reduce the speed in order to increase its pulling capacity, and that’s why we use gear systems. Gear systems reduce the effective angular velocity of the motor, thus increasing its torque and pulling capacity. Hence, Reduce Speed –> Increase pulling capacity –> Use Gears
There are different types of wheeled locomotion systems. They are listed below. Each locomotion system is unique, has some advantages and disadvantages. We will discuss them one by one.
- Differential Drive
- Car Type Drive
- Skid Steer Drive
- Articulated Drive
- Synchronous Drive
- Pivot Drive
- Dual Differential Drive
This is the most popular and widely used type of drive for wheeled robots, because it is the simplest and easiest to implement. There are two motors, each having an independent motion. In the first two diagrams shown above, both the motors are rotated in same direction of motion and thus the robot moves either forward or backward. In the last two diagrams, the two motors rotate such that they oppose each other’s motion, thus generating a couple and creating a turning effect.
- Simple and easy to implement
- Arbitrary motion can be achieved
- In-place rotation (zero radius) can be done
- Difficult to maintain straight line due to independent motors
Car Type Drive
This is the type of drive most common in real world but not in the robotic world. Here, we have a pair of wheels which direct where the robot should move, whereas movement is brought about by a different set of wheels. Translatory motion is provided by the rear wheels whereas rotational motion is provided by the front wheels. Though both motions are independent, but their interlinking results in greater accuracy.
- Replicates the real world
- Difficult path planning
- Inaccurate movement
- Slight inaccuracy results in huge errors
- No direct directional actuators available
Skid Steer Drive
It is a close relative of the differential drive system. Here, all the motors of one side are tied together as one to increase traction (e.g. tanks). Only the center motors are connected. The remaining motors move due to the force of the central motors. During turning, the wheels skid/slip over the surface. Turning can occur due to difference in the motion of the two motors.
Its properties are similar to the differential drive system, except that it provides greater traction and has quite inaccurate position tracking.
Here, the body/chassis of the robot is deformed to produce rotatory motion, whereas the translatory motion is provided by the wheels. Two motors are required, one for translatory motion (wheels) and another to change pivot angle (for the linear actuator).
Rest other features are similar to the car type drive.
Here, the robot can move in any direction without changing its alignment. Two sets of motors are required, one to drive the wheels, other to change their direction. This is clearly shown in the diagram above.
It has synchronous operation and greater accuracy. It is a bit complex to build, but simpler to use!
This is a unique type of drive system. There is a four wheeled chassis which gives translatory motion and a rotating platform which gives rotational motion. Thus, it achieves accurate straight line motion. While turning, the raised platform is lowered such that it lifts the chassis, rotates by desired angle, and then is raised again to keep the chassis back on the ground. This can be achieved using one/two motors, depending upon the complexity and requirement.
Dual Differential Drive
This is similar to differential drive, but uses special gear assemblies, which increase the accuracy of straight line motion and on-spot turning.
So this was all about the different types of wheeled locomotion systems. In the next post, we will discuss about different types of actuators in brief. Please comment below if you would like to share some of your thoughts!
To stay updated, subscribe to this site and/or grab the RSS Feeds! See you soon!
Some (not all) images and information has been taken from the materials of Technology Robotix Society, IIT Kharagpur.